![sync digital performer with resolume arena sync digital performer with resolume arena](https://i.ytimg.com/vi/LCGppUGktb0/maxresdefault.jpg)
Now for this portion I realize that the majority of you don't own a lot of lights, so you may have to rent them. Then at about a 45° angle sew up from the seem to the top Then make some cuts on the folded over side, for all the connecting pieces. Your pvc pipes will slide in to this hem so leave room. Take a large piece of spandex the length of the bottom rail of the pyramid and fold it over about two inches and make your hem. That seemed like a long complicated rant to you as well huh? That's why I took pictures :) This 45 and the top 45 can mow be measured and cut. The ends of the bottom rails will be as follows starting from the T on each side. By now you should be able to see the length in which you need to cut the bottom of the 90° braces. the 90° brace pieces we made earlier can now mark how far out you need to make your cut in the bottom rail so you can insert a T. After that you will attach your 2 bottom rails leaving them long enough to meet up with each of the outside 45° angles of the pyramid. To do this we just kind of have to eyeball out the front 45° angle and measure out the length you need to achieve the height you have decided on. Before finding the length we need to cut the bottom piece of the 90° brace to, we need to lay out the middle upright. So figure out how tall you need your pyramid and cut 2 pieces of pvc that length for the 90° angle braces we will be connecting to each side of the top rails then to the offset middle of the bottom rails. Also to have this make more sense in your head, essentially we are making a 4 sided pyramid only leaving the back open, because you will not see it and also it gives access to the DJ's. Now is the time that you should make sure the length of your top rails will cover to the edges of the table so you don't see it. The bottom rail starts out the same in the center 45° > spacer > T > spacer > 45°, only this time the single side of the T will be pointing up toward the top rails T they will connect eventually. From the downward facing point of the T we will make a 90° brace from top rail to the bottom rail on each side, in order to not tip over.
![sync digital performer with resolume arena sync digital performer with resolume arena](https://videomapping.store/wp-content/uploads/2017/04/hqdefault-1.jpg)
Note: do not glue anything together until you get through the 1st dry run, then you can mark a line on each of the connections so you can glue them in the exact same place later.Įach of the sides of the top rail will also consist of T > spacer > 45°, only this time the t will face straight down with one side to connect to the top rail, and the other side will be, spacer > 45° facing toward your bottom rail of each side. Then connect a 45° angle piece to each of the 2 spacers these will hold the top rails so angle accordingly.
![sync digital performer with resolume arena sync digital performer with resolume arena](https://uploads.toolfarm.com/app/uploads/2020/12/21100448/resolume_731update.jpg)
Insert them in eash side of the T with the center of the T pointing down and at a 45° angle forward. Take a T connector and 2, 2" pieces of the pvc (lets call these spacers). We will start by building the top of the lower portion of the pyramid, by starting in the middle. Then we can get started building the framework for the pyramid. Now that we know the base we need to cover with the pyramid, we also need to know the size of the stage we are using in case we have any size limitations. So if you pick up a set of 4 bed raisers, found at any local big box store, and put them under the legs of the table they will thank you for it. In most cases a 4x8' table will be large enough, but usually they like it a bit taller so they don't have to slouch. Lets get started by choosing the table your artists / DJs are going to want to use.
Sync digital performer with resolume arena plus#
Plus the fabric is easy to project onto, and stretches tight around the frame giving a clean look with 1 seam barely noticeable. This system is light, and modular I can fit the whole pyramid into 1 bag made to carry truss in. I have chosen to make my life a little easier and cheaper by using fabric and pvc on this project for a few reasons.
Sync digital performer with resolume arena skin#
Ok so there are a thousand ways to skin a cat so they say. What we will need for this is a sewing machine, white spandex or stretchy material, PVC tubing, a cutter, and a lot of connectors ( T, 45°, 90°).